Aftermarket thermocouples, muffle heaters and heating elements for dental porcelain and zirconia sintering furnaces. Every part is manufactured to match the dimensions, connectors and temperature characteristics of the original component.
Platinum/platinum-rhodium (Pt10Rh–Pt) replacement thermocouple for high-temperature zirconia sintering furnaces up to 1600 °C. Calibrated wire pair, ceramic twin-bore insulation and furnace-specific connector on request.
Replacement type K (NiCr–NiAl) sensor for dental porcelain and ceramic firing furnaces up to 1200 °C. Fast response, drift-resistant design, supplied with matching connector.
Quartz muffle heater replacement for dental porcelain furnaces. Wound to match original resistance and watt density for identical heating curves and vacuum performance.
Silicon carbide replacement heating elements for zirconia sintering furnaces with resistance-matched pairs for even furnace chamber temperatures.
Dense-sintered alumina (99.7 %) twin-bore and single-bore ceramic tubes to protect noble-metal thermocouple wires in sintering furnaces.
Coil-type replacement heating elements for dental burnout and wax elimination furnaces, matched to original resistance values.
Aftermarket molybdenum disilicide (MoSi2) heating element replacement — compatible with high-temperature zirconia sintering furnace families such as Nabertherm LHT 01/17D, VITA ZYRCOMAT 6100 and Sirona inFire HTC. A 1700 °C-capable element, matched to the original geometry and watt density.
Aftermarket noble-metal type S thermocouple replacement compatible with Programat S1/S2/S3 zirconia sintering furnaces. Calibrated Pt/Pt-Rh wire pair up to 1600 °C with the matching dimensional and connector profile.
Aftermarket recrystallized silicon carbide (SiC) rod element replacement compatible with zirconia sintering furnace families from Zirkonzahn and Amann Girrbach. Supplied as a resistance-matched set for even chamber temperature.
Aftermarket quartz muffle heater replacement compatible with VITA Vacumat series porcelain furnaces. Wound to match the original resistance and watt density for identical heating curves and vacuum performance.
Aftermarket type K (NiCr–NiAl) sensor replacement compatible with VITA Vacumat and Programat series porcelain furnaces. Fast response and slim sheath, supplied with the matching furnace-specific connector.
Aftermarket door seal and gasket kit compatible with common porcelain and sintering furnace muffles. Compressed and perished seals let heat escape, so replacing them restores cycle times and temperature hold.
Aftermarket thermocouple extension and compensation cable in type K and type S grades. Damaged leads cause drift-like errors; factory-fitted connectors give a clean, polarity-correct replacement.
Aftermarket sintering tray for zirconia restorations, resistant to thermal shock and repeated 1500 °C cycles. Sized to fit common sintering chamber beds.
Aftermarket type B (Pt30Rh–Pt6Rh) thermocouple for the highest-temperature sintering and laboratory furnaces above 1600 °C, where type S sensors exceed their rated range.
Aftermarket coil-type muffle heater replacement compatible with Nabertherm burnout and preheat furnace families, matched to the original resistance and coil geometry.
Aftermarket ceramic terminal blocks and heater clamps for replacing corroded heater connections. A corroded terminal mimics heater failure symptoms at a fraction of the cost of a new element.
No products found in this category yet.
A drifting sensor is the most common cause of dull glazes, changed translucency and failed sintering results. We supply type K (NiCr–NiAl) sensors for dental porcelain furnaces and calibrated type S (Pt10Rh–Pt) elements for zirconia sintering furnaces — each matched to the tolerance class, insertion length and connector of your furnace model.
Slow heat-up or a final temperature that is never quite reached usually means the muffle heater is worn out. Our quartz muffle heaters are wound to the original ohm value, and our resistance-matched SiC element sets keep zirconia sintering furnaces even from edge to edge — both pre-tested so the controller needs no recalibration.
Send us your furnace brand, model and — if known — the part number printed on the old component. We confirm the matching replacement within one business day and reply with price and lead time.
No. We sell new, independently manufactured aftermarket parts that are dimensionally and functionally equivalent to the originals. All brand names are used only to indicate compatibility; we are not affiliated with any furnace manufacturer.
Yes — we ship worldwide from our warehouse in Montenegro. Stocked parts leave our warehouse within 48 hours; delivery to Europe typically takes 2–4 working days.